dash lights dodge journey

Dodge Journey Dashboard Warning Lights (All Models 2009 to 2020)

Welcome to the ultimate guide to all dashboard symbols, warning lights, errors and faults for the 2000 to 2020 Dodge Journey. This will assist in troubleshooting, diagnosing and solving common automotive problems with this specific car.

Please note: This guide covers every single possible symbol/warning light for ALL model variations for Dodge Journey, including standard, premium and top-of-the-line models, plus variations in body shape. While this guide does cover your specific vehicle , your car may not have all the symbols featured on this list.

Dodge Journey Symbols and Warnings Guide

There are 25+ possible lights that may illuminate for a variety of reasons.

While this guide is helpful, please refer to your owner’s manual after reading through this list.

Dodge Journey Engine Fault

There are hundreds of reasons why the check engine warning fault light comes on, and only your dealer or mechanic is qualified to address this.

Common reasons include a loose fuel cap, excess vibration, a blocked cylinder, a bad fuel mix, excessive heat and half power.

This may also highlight an issue with your transmission.

Dodge Journey Check Engine Oil

This means your engine oil is running low or has been completely drained. Your engine may have an extensive oil leak and a mechanic will be required urgently.

At this stage, it’s not recommended that you drive your vehicle.

Dodge Journey Attention / Warning / Fault Detected

Either of these two lights will illuminate to get your attention to other dashboard warning lights and symbols.

These lights can also mean that the handbrake is engaged.

Dodge Journey Battery

This means your battery has low voltage and may need a replacing.

Should you choose to drive your vehicle with a faulty battery, you risk losing power to your battery at high speeds.

Many mechanics will prefer to visit your home to replace your car’s engine battery, rather than have you drive to them.

Dodge Journey Press Foot Brake

This symbol is your Dodge Journey telling you to press the foot brake.

This is required before starting the engine and moving the vehicle out of Park.

Dodge Journey Handbrake Engaged

Your handbrake is engaged.

This can be disengaged by hand, or your vehicle may have a handbrake that is disengaged with your foot.

Dodge Journey Airbag Fault

This means your driver’s side or passenger side airbag has a fault and may not deploy when required. However, it’s quite common for this light to illuminate due to a faulty sensor, rather than a faulty airbag.

Take your vehicle to your mechanic for inspection as soon as possible.

Dodge Journey High Radiator Coolant Temperature

This symbol represents excessive heat from your engine’s radiator. If ignored, you risk overheating your engine very quickly.

Common reasons are a low coolant level and a leak in the radiator.

Call or visit a mechanic immediately.

Dodge Journey Parking Sensors

This symbol represents the front or rear parking sensors. You will also hear an audible beep as you get closer to a wall, pole, tree or other object when reversing.

Dodge Journey Bulb Not Working

This means one of your driving lights has stopped working and requires either a bulb replacement or fuse replacement.

Dodge Journey Low Beam Lights On

This means your front standard driving lights are on.

These lights are used for 99.9% of driving.

Dodge Journey High Beam Lights On

This means your front high-beam driving lights are on.

These lights are used for 0.01% of driving and typically for country roads late at night. Fines can apply for use of high beams in dense residential areas. Do NOT use high team driving lights within 400 metres (1,000 feet) of an oncoming car.

Dodge Journey Automatic Low Beam Lights On

This means your front automatic standard driving lights are on.

These will illuminate by themselves on dusk, when entering tunnels and in other low light situations.

Dodge Journey Automatic High Beam Lights On

This means your front automatic high-beam driving lights are on.

Please be wary that these lights do not turn themselves on automatically around other cars.

Dodge Journey Automatic Lights Malfunction

Dodge Journey’s come with automatic lights, however, these can malfunction.

This is often an issue with the front low-light sensor. You may continue to drive and simply use your normal on/off headlight function until you visit a mechanic.

Dodge Journey Glow Plug Indicator Symbol

This is the Glow Plug Indicator symbol, which is found only in diesel-powered variants of Dodge Journey. Diesel engines require heat in the cylinders to operate, which is supplied initially by its glow plugs when the engine is freezing cold.

When illuminating green, this is operating perfectly but when yellow, a fault may exist.

Dodge Journey Vehicle Is In Park

This means your vehicle is in Park.

Dodge Journey Hood / Bonnet Is Open

While your front hood/bonnet may appear closed, it may show open on the sensor.

Dodge Journey Front Fog Lights Enabled

This means your Dodge Journey front fog lights are engaged. A similar symbol exists for the rear warning lights.

Note: In some areas, it is illegal to use fog lights when it isn’t foggy. Please check with your local authority.

Dodge Journey ABS System Fault / ABS System Off

Your vehicle’s ABS system has a fault and may not engage under heavy braking.

Please visit a mechanic as soon as possible.

Dodge Journey ECO Mode On

ECO mode in a Dodge Journey is an optimum driving mode.

Your throttle will not respond favorably to performance driving.

Instead, your fuel economy will be at its best, hence the term ‘Eco’.

Dodge Journey Truck / Boot Open

While your rear trunk/boot may appear closed, it may show open on the sensor.

Dodge Journey Front Radar Engaged

This means your front sensor is engaged.

This feature provides autonomous braking and adaptative cruise control.

Dodge Journey Lane Assistant On

This means your lane-keeping assistant is on.

This feature allows your vehicle to remain straight within its lane.

This may only engage above 40km/h or 25mp/h.

Dodge Journey ESP / ESC Engaged

This means your Dodge’s Electronic Stability Programme (or Electronic Stability Control in some countries) has been engaged.

This typically engages on wet, muddy or icy roads.

Dodge Journey Check Brake Fluid

This means your brake fluid has become low and may require topping up.

Dodge Journey Check Brake Pads

This means your brake pads have become low.

This may be difficult to check and may require visiting a mechanic as soon as possible.

Dodge Journey Steering Wheel Locked

This means your steering wheel is locked.

This is an anti-theft symbol that flashes when your vehicle is locked.

Dodge Journey Service Due Soon

This means your vehicle is due for servicing soon.

Your mechanic may have programmed an alert within your car’s computer to illuminate this symbol upon crossing a certain odometer reading.

Dodge Journey Heated Seats

This means your heated seats are on.

The number of vertical lines represents the level of heat.

Dodge Journey Cruise Control Activated

This means your cruise control has been activated and is ready to use.

However, your cruise control will not be on. It’s simply ready to switch on.

Cars often use 2-buttons to avoid accidentally turning on cruise control.

Dodge Journey Check Wheel

This means you have an issue with your wheel.

This isn’t the rubber tire but the wheel itself.

Issues include alignment, steering and balance.

Dodge Journey Heated Windscreen

This means your windscreen is being heated to melt frost or ice.

This may turn itself off automatically.

Dodge Journey Air Suspension Fault

If your Dodge Journey has air suspension, then this symbol represents a fault.

This could be a deflated rear suspension air bag, an air leak or a sensor issue.

Dodge Journey Tire Air Pressure Fault

This means your tire pressure is either too low, or the sensor has faulted.

This requires calling or visiting your dealership as soon as possible.

Dodge Journey Intermediate Windscreen Wipers On

This means your automatic windscreen wipers are on. No action is required.

Ultimately, your car is trying to tell you something. You should consult your owner’s manual and have your car inspected by a qualified mechanic as soon as possible.

Symbols Have Different Colors

Much like traffic lights, the color of your dashboard symbol light is just as important as what it means. The lights can also flash to draw your attention to a more severe and time-sensitive issue.

When a Dodge dashboard warning light is green or blue, they are simply telling you that one of your car’s features is being used, or has been activated. No action is required at this time.

When a light is yellow, your car is trying to tell you that a less common safety feature of the car is being used (such as stability control on wet roads), a mild fault has been detected or a repair may be required. If you’re unsure, you should seek the services of a mechanic or dealership as soon as possible.

Orange or Red

If the dashboard on your Dodge is orange or red, this can be a signal that your vehicle is experiencing a problem that needs urgent attention . You MUST call or visit your dealership or mechanic immediately.

This dashboard symbols guide is for entertainment and informational purposes only, and does not replace seeking professional advice from a certified technician or expert mechanic. Please consult with a certified technician or mechanic if you have specific questions or concerns relating to any of the topics covered herein. Under no circumstances will DashboardWarningsLights.com be liable for any loss or damage caused by your reliance on any content on this website.

Joshua Lee is the writer, editor and owner of DashboardWarningLights. Joshua has a deep obsession with the automotive industry, for both passenger vehicles and trucks. When he isn't writing or driving, he enjoys exploring in the great outdoors!

Dodge Journey Dashboard Lights And Meaning

Dodge Journey is a crossover SUV car marketed by FCA’s Dodge Brand (2009) that gives you a potent engine along with Low starting price. Its infotainment system is so trouble-free to operate with more user -friendly technical features.

This car highly appealed to a next-level performance with comfy driving. It comes with an excessive lean body that makes its infrastructure more stylish and upgrades your status. 

Such trendy cars are composed with so many warning indications displayed on the car’s dashboard. It highlights the malfunctioning of the system’s components, security issues, and immediate maintenance whenever needed. It is highly suggested not to neglect these lights as it can risk the safety of the driver.

Look below the warning lights that demonstrate the respective meanings of these indications.This Dodge Journey dashboard warning lights guide also let you to go through the actions that should be implement when these warnings flickers. You can also refers the other models of Dodge on our site like Dodge Charger, Dodge Durango,  Dodge Challenger and Dodge Ram Truck.

Dodge Journey ABS Warning Light

This dashboard symbol activates to indicate a malfunction in the Anti-lock braking System of your vehicle. In this scenario, you can still use your conventional parking brakes without the assistance of ABS. Later you have to inspect your car at Dodge service centre.

Dodge Journey Air Bag Warning Light

If this dashboard light flickers on your dashboard then it indicates a problem in the airbag system and it could not puff out in a crash or a hit. In this case, get serviced your airbag fault from nearby Dodge service centre.

Dodge Journey Battery Charge Warning Light

This warning light gets turn on when the battery is not adequately charged. If this light stays on for a long time, it indicates some malfunction in the charging system. Go and check your vehicle in the service centre.

Dodge Journey Brake Warning Light

This dashboard light gets active when the parking brake is applied or there is a fault in an anti-lock brake system, may be the brake fluid level is getting low in your vehicle. Suppose this light stays on for a longer time than it indicates that parking brakes are disengaged. So, release the parking brakes as earliest. And if this light is still on then go check your vehicle by Dodge service centre.

Dodge Journey Door Open Warning Light

This light gets activated when the Doors of your Dodge journey remain open and not closed properly.

Dodge Journey Electric Power Steering Fault Warning Light

This dashboard light activates when the electric power steering system is detecting a fault in it. If you continue your drive in this warning light, it can create a risk to your safety.

Dodge Journey Electronic Stability Control Active Warning Light

This dashboard light activates on your Dodge Journey Dashboard to indicates that the stability control system is activated in your car, and it is all set to assist you with the road grip and stability.

Dodge Journey Electronic Stability Control Off Warning Light

This warning symbol illuminates on your Dodge Journey dashboard to indicate that the Electronic stability control system is off in your vehicle. Now it will not assist you in controlling your car.

Dodge Journey Electronic Throttle Control Warning Light

This dashboard light gets activate when it indicates a problem in the electronic throttle control system. In this case, completely stop your vehicle and place it in a PARK position. If this light stays on for a long time, then it may reduce your vehicle performance.

Dodge Journey Engine Check Malfunction Indicator Warning Light

This light displayed on the Dodge Journey dashboard to indicates any malfunction in the engine. This light associates with the Automatic Transmission control system and engine monitoring of your vehicle. In this light, we highly advised you to contact dodge service centre.

Dodge Journey Engine Coolant Temperature Warning Light

This warning light activates to alert the driver that the engine of a vehicle is overheating. If this coolant temperature becomes high, then it indicates the chime sound. In this case, a driver should immediately stop the car and turn off the air-conditioning system. Shift your vehicle into the NEUTRAL transmission and idle the vehicle. Immediately switched OFF your system and called for service and maintenance.

Dodge Journey Engine Oil Pressure Light

If this warning light flickers on your Journey dashboard, then it indicates that your engine\'s oil pressure is getting lower. In this situation, please turn off the ignition and stop your vehicle to check its oil level. If the oil level is average, then you should contact to the Dodge service station as earliest.

Dodge Journey Front Fog Indicator Light

This dashboard light gets turn on when front fog lights are activate in your Dodge Journey.

Dodge Journey High Beam Indicator Light

This dashboard light activates when headlights are activated in your vehicle. In this case, push the malfunction lever forward to turn Off the high beams of your Dodge journey. If high beams are still ON, then pull the lever towards your direction to temporarily activate the high beam.

Dodge Journey Low Fuel Warning Light

This warning light indicates when your fuel level reaches 2.7 L, and It stays on until you add some fuel to your vehicle\'s fuel gauge.

Dodge Journey Low Washer Fluid Warning Light

This warning light gets activated when the washer fluid is getting low in your Dodge Journey.

Dodge Journey Park Headlight On Indicator Light

This warning light gets on when the headlights of your Dodge journey are activated.

Dodge Journey Seat Belt Reminder Warning Light

This dashboard light activates whenever the driver or any passenger\'s seat belt remains unbuckled. If this light remains on for a long time and continues to flash, then you should immediately check the seat belts of all the seats of your car.

Dodge Journey Speed Control Fault Warning Light

This dashboard light indicates when the cruise control system is all set to the desired speed.

Dodge Journey Tire Pressure Monitoring System(TPMS) Warning Light

This light activates along with a pop message on the dashboard that your vehicle\'s tire pressure is getting lower than the recommended values. Check all the tires by Dodge Service Station.

Dodge Journey Transmission Temperature Warning Light

This dodge journey dashboard light gets on to alert that the transmission fluid temperature is getting high. In this case, stop your vehicle and engine. Shift to the NEUTRAL position. When this light gets turned OFF, then you will continue driving.

Dodge Journey Turn Signal Indicator Light

This dashboard light gets turn on to alert the driver that your vehicle is driven more than one mile, or we can say 1.6 km with the turn signal on. This light flashes until the left, or right turn signal is activated.

Dodge Journey Vehicle Security Warning Light

This dashboard light activates on your Dodge Journey instrumental cluster when the vehicle security alarm is ringing, and it flashes slowly when the vehicle is disarmed.

Other Models

Audi A6 Tire Pressure

Chevrolet Impala Owner’s Manual

Chrysler 300 Tire Pressure

Chevrolet Cruze Tire Pressure

Fiat Qubo Dashboard Lights And Meaning

Skoda Superb Dashboard Lights And Meaning

Peugeot 308 Dashboard Lights And Meaning

Subaru WRX Dashboard Lights And Meaning

Chevrolet Malibu Dashboard Lights And Meaning

Mercedes Benz S-class Dashboard Lights And Meaning

© 2023 warningsigns.net

DASH-LIGHTS.COM

Dashboard Warning Lights Explained

Dodge Journey Dashboard Warning Lights

64 thoughts on “ dodge journey dashboard warning lights ”.

My dash board lights only goes off for like 10minutes and then comes back on permanently after turning off the engine and locking the car doors. this drains my battery

I got a warning light that I can’t find in my manual or on line. It looks like a screw in the side of the vehicle. Can you tell me what it means?

Hello Patricia, Are you sure the car and screw warning light is not a loose gas cap symbol?

I checked these on mine but did not affect car with large screw hovering.

I just got that light today…is it the gas cap

Put antifreeze in the car gauge says the oil temperature is rising the transmission fluid temperature is rising and the coolent temperature is rising and says 5470 engine hours what does this mean

Hi Wanda, How old is the existing antifreeze? If it’s several years old, it may require flushing, else there may be sludge build up resulting in the system getting blocked. Transmission systems can also make use of the car’s cooling system and can overheat if there’s a problem. Also check your char’s water pump. The engine hours is referring to how many hours your engine has been in operation over its lifetime.

Patricia I had the dame this last week and even the mechanic had never seen it I checked the gas cap, took if , screwed it in again, but no change. Had the lugs tightened on wheels though he said they were fine= zi have NO IDEA. It bothers me that it’s not in the manual

2014 Dodge Journey: 3 warning lights came on simultaneously. Oil which is full, tired which are filled to spec. and eve light. What causes this and how do I fix it?

Hi Tom. Rather than ‘eve light, did you mean ABS light? Sounds like sensor issues. I would concentrate on the oil light initially as this is the most serious and have your engine pressure checked. If it’s good, it may be the oil pressure sensor.

My 2009 Dodge Journey’s instrument panel completely lights up when shifting from 1st to 2nd. You can feel a slight jerk and click. Tranny works fine but the dashboard is completely lit up. I already reset the dashboard but it comes on immediately when shifting from 1st to 2nd.

Round red light came on three times went out each time what is this red dot panel with rpm’s

Hi Yolanda. I think it’s the vehicle security warning light. Have you changed or disconnected the battery?

I have a 2009 Journey. Sporadically, the ESC light will come on, and the car starts running very rough….almost to the point of stalling. However, if I keep a steady flow of gas, it doesn’t stall on me. Do you know how the gas and ESC error light would be related causing the car to run so badly? Thank you!

Hi Amy, Part of the ESC (Electronic Stability Control) system is to cut engine power and can also apply braking. This helps with traction (preventing wheel spin), oversteer and understeer. If the system is faulty, it could be engaging when it’s not supposed to and giving you the rough engine and problems accelerating. This could be something as simple as a wheel speed sensor that’s at fault, or the ESC module, steering angle sensor.

On my dashboard. Red light came on.and i can’t find the red light symbol.i have a 2010 dodge journey.i have look up the symbols on my phone and i can’t find that symbol.

Hi Loretta Can you describe the light?

I’m having a similar problem as Amy. Sometimes my ESC light will come on and it says OFF though. Basically ESC OFF it shows the image, but it says OFF. It happened today. I turned on the car and the light came on and I had to get in the interstate and I was going 70+MPH and whenever I would let my foot off the gas and the vehicle would stutter and feel like it wanted to stall. The MPH would begin to drop and I wasn’t able to increase by speed. It would drop to about 60 MPH and then I would be able to increase by speed again..I have a 2011 Journey.

I am having the same problem…did you ever figure out how to fix it??

2018 Dodge Journey check engine light and it woo t switch gears. It will jerk really hard then it won’t switch gears

I have a flashing “Dodge” symbol that flashes then remains on for a short time. The tipm has been replaced. Could it be a reset is needed?

What does red ‘Back’ light mean

what does it mean when the letters PSI come on?

On my 2010 Dodge Journey. The Eps light is staying on

My dodge journey yellow light has just come up. Although today I’ve had new tyres and rims fitted have you any idea as to why if so any help will be appreciated thanks

Hello Kelly, I assume you mean the tyre pressure warning light? The tyre pressure light coming on after having new tyres fitted is usually a sign that a sensor has not been fitted, not been fitted correctly or damaged during the tyre fitting service.

I have a stupid question! Do I turn on the slippery car symbol when I’m driving in the snow?

Hi Janie, No, don’t touch it, it will automatically be on already. If you press the button so that the slippery car symbol illuminates, you’ll be switching the system off. On most cars it’s called electronic stability control (ESC) or something similar. ESC comes on automatically each time you start the car.

If you happen to get stuck in snow and can’t get out, you might need to rock the car backwards and forwards. In this situation, you press the ESC button (slippery car symbol), or the traction control button to deactivate traction control. By leaving traction control on, it’ll stop or reduce wheel slip, but if you’re stuck in snow, you want wheel slip to help free your vehicle. Once you’re free from the snow, press the button again to switch on ESC.

Hello, I have a 2016 journey and I get the ETC and the ESC indicators on. Usually I pull over, turn off the car and wait a few seconds but now it’s happening more often. What is this and how can I fix it?

Hello, my ETC and my ESC have started to come on, more in the past 2 days. What should I do to fix this? I have changed the alternator and the battery and it still keeps coming on

Hello Al, The throttle sensor is quite a common fault with the Dodge Journey. The throttle body might need to be replaced.

My etc light came on and now the car isn’t starting what do i do? its not even turning its my moms car and she’s on vacation

Is the car turning over? Things to check are battery charge and connectors. Throttle body is often an issue, sometimes to do with the sensor.

Hello, I have a 2014 journey and I get the ETC and the ESC indicators on. Usually I pull over, turn off the car and wait a few seconds but now it’s happening more often. What is this and how can I fix it? Now it barely even starts half the time what is wrong?

Hi Angel, It’s usually to do with the throttle body. Usually throttle control sensor or position sensor, sometimes the wiring. An issue with the throttle may disable the ESC, so sorting out the throttle issue is likely to fix the ESC issue.

Battery died.Had it jumped.Cars great never any problem. We under reaio are buttone to push for Air, a C button, from, rear ans slippery traction. We t g we button next to air that has C on it bliks :& I don’t know ow if could be a fuse of something more serious My husband fixed these problems but he passed suddenly 90 days ago Can someone answer my question please. I’m in Florida and you can’t dive In aug8with no circulating air. I’m at [email protected]

I have a 2011 journey with 131791 miles on it for the 1st time since owning it in the little center window it’s showing what gear I’m in p r d but it also has a round clock like light right next to the gear light what does that mean I have had nothing but problem’s with this piece of junk the Camara quit heated seats quit had to replace a heater core had to replace head gaskets battery altanator brakes every 1 1/2 years in front worse car ever owned some how front drive shaft got bent or something so the whole car,s vibration was so bad you could not drive the thing .

Hi Dean, Sounds to me like you need to get rid of ASAP. I’m afraid I’m not too sure. Looked into it and can’t find any info. All I can think is that it’s symbol of a reminder – maintenance / service? Hopefully someone else will know.

Hi, there. When I was driving my 2014 Dodge Journey on hyw feeling the car was shaking, I could see my arms were shaking, about half hour later sign on the middle screen looks like a double lined Red Cross while a Ding sound, and disappear soon. Then I got out the Hyw, the shaking was disappeared on 50km/h. Anyone know what’s the sign for? Just changed my tires at Costco three month ago.

I have a 2014, when I put it in reverse a over look of the vehicle comes up on the dashboard with a SERVICE light under it and a dinging sound comes on. This has been going on for awhile, the rear camera works fine and has not ever been damaged. Any ideas on if this is a normal thing or is it something more?

My 2012 journey has a small red polite and a exclamation icon red in colour be for it what does it mean can’t find a explanation any were it is on the rite round dash gauge thanks

Hello everyone while reversing today for my dodge Journey 2018, I noticed a sign came up on the reverse showing clean what does that mean

Hi Teddy, Could it be to do with the backup camera or ParkSense sensors that need cleaning? The ParkView camera is located on the rear of the vehicle above the rear license plate and the outer surface and the underside of the rear fascia/bumper require cleaning and kept clear of snow, ice, mud, dirt or other obstruction for the ParkSense sensors.

I have a 2015 diligence journey. Every now & then going downhill I get an ! Mark and a P. Both are in red circles. Mai

Hi Mai, I should have your vehicle braking system serviced. Always best to have anything to do with brake issues checked out right away. It is worth checking under the hood at your brake fluid levels, as this level will fall over time as brake pads wear low. Also keep an eye on brake pads, they require replacing after a while.

The ETC Light and the traction light lit up. What does this mean? Is it because my air tire pressure is low?

Hi Betsy, It’s unlikely to be related to tire pressure, but it’s best to keep tire pressures up to the recommended values as stated on the sticker inside the door jamb. This will improve stability and fuel consumption. The Dodge Journey does have issues with the throttle body, often needing replacement. This fault can trigger reduced engine power mode (limp home mode) and often systems such as traction control can be automatically deactivated as a result.

What is the small red P with a ! Red icon be for it mean on my 2012 dodge journey it is in the rite round dash gauge

Hi Doug, I’m not sure either I’m afraid. All I can think of is a problem with Park (P). If it would be parking brake related, it would be contained in a circle and parenthesis.

In 2014 dodge journey..the inside lights flashed on and off for 2 minutes while dash had a dinging sound..stopped for a minutes started again..lasted 15 minutes til I got home.. what’s this mean??

Hi Alicia, Is it a specific timed flashing or more of a sporadic flickering? There are some issues with Dodge Journey’s with flicker interior lights, or lights staying on which is related to bad wiring / short issues. A wire that controls lighting to the trunk is a common culprit.

Hit a large pothole and now the ads light along with other lights come on. Sometimes the lights will come on when turning on the ignition and other times it does not. I was told that this could be a wheel bearing problem or an ABS shortage anyone have any ideas.

Hi Eugene, Yes, as you say, wheel bearing is a possibility. There’s also a wheel speed sensor located at each wheel, these sensors are prone to damage and that could also be the issue. If you’re noticing any noise from the particular wheel that hit the pothole, humming noise, looseness in the steering, vibrations etc, this may also be a symptom of a damaged wheel bearing.

Hi I have a 2014 dodge journey and my engine light came on and hasn’t gone off I had a service last week and nothing was bought to my attention. We had a -1 degree morning and the car was frozen could this have an impact on this light coming on?

Hi Kelly, Yes the colder weather can impact on your car. Usually though, it’s the cold weather, triggering the engine light that’s making an already underlying problem worse, hence the light. There’s no way of knowing why the engine light is on other than having diagnostics. When the engine light comes on, you’ll typically have a fault code generated and stored. A diagnostic OBD II tool is used to scan for the codes and point you to where the fault is. You should be able to find an auto workshop where you’ll receive a free diagnostics check.

I had a Throttle Replacement a month ago, for my 2014 Dodge Journey with 67,000 miles at the Dealership. No w, a red sailboat light with a chime just came on. What could this mean. Please help, thank you!

Hi Dionne, A sailboat light? It’s not the engine coolant light is it? (see above)

Hi My Dodge Journey stx 2012 model 3,6 shows slippery Warning light, ABS, Brake and constantly feels like its going to cut but doesn’t cut at all. What it might be?

Hi Xolani, I should check your brake fluid level. A common cause for the ABS and slip indicator light to come on is a faulty wheel speed sensor. However, as your brake light is illuminated, you should have any fault codes read with a diagnostic scanner right away.

Leave a Reply Cancel reply

You must be logged in to post a comment.

Vehicle Manufacturers

• Mercedes-Benz

Vehicle Type

• Commercial Vehicles

Warning Lights

• Dash Warning Lights
• Car Warning Light Colour Meaning
• Privacy Policy

Home » Troubleshooting » Dodge Journey dashboard lights flicker and won’t start – causes and how to fix it

Dodge Journey dashboard lights flicker and won’t start – causes and how to fix it

Flickering dashboard lights in Dodge Journey when attempting to start the engine might seem like a major malfunction has occurred, but in the majority of cases it’s not a serious cause for concern.

The most common causes for flickering dashboard lights and no engine crank in Dodge Journey are weak battery, corrosion on battery terminals, and bad ground connection.

1. Weak battery

The leading cause of flickering dashboard lights and no start in Dodge Journey is weak battery. You may also hear rapid clicking noise when you try to start the engine. If there isn’t enough charge in the battery to power the starter motor, and you try to crank the engine, the battery voltage will get so low that it can’t properly power the lights, accessories and of-course the starter.

Symptom: Rapid clicking sound

How to test the battery in journey.

The easiest method to check the 12v battery in Journey is by measuring the voltage with a multimeter. A healthy battery should have 12.6 volts or more when fully charged. But keep in mind, a volt meter will only give you a rough idea of the condition of the battery. Sometimes a battery showing over 12.4 volts may not be able to supply enough current to crank the engine.

Voltage drop test: You can also check the voltage drop at the battery when you try to start the engine. If the voltage drops too much, below 10 volts, your battery doesn’t have enough charge to start the engine. This can happen due to internal degradation of the battery, if the vehicle has been sitting for a long time, or if the alternator in your Journey has malfunctioned and not charging the battery properly.

How to jump start Journey

To rule out dead battery, your best course of action is to jump start your Journey using jumper cables and a healthy battery from another vehicle, or using a battery booster if available. Requirements: The engine of both the vehicles should be off, and the transmission in Park.

• Connect the red cable to the positive terminal of the dead battery in Journey.
• Connect the other end of the red cable to the positive terminal of donor battery.
• Connect the black cable to the negative terminal of donor battery.
• Finally connect the other end of the black cable to any bare unpainted metal part of the body or engine of your Journey. Safety warning: Connecting black cable directly to the negative terminal of Journey battery can ignite flammable gases from the battery due to sparks.
• Start your Journey.
• Remove the cables in the reverse order.

Warning: There is always a risk of burning up the alternator or other electrical components if the engine of the donor battery vehicle is running during jump start. Therefore it is recommended to keep the engine of the donor vehicle off when jump starting your Journey.

Recommended video

2. Poor battery connection

It is possible the battery in your Dodge Journey is in good health, but the current flow is interrupted due to loose electrical connection, damaged wire, or corrosion on the battery terminals.

Corrosion on battery terminals

Battery corrosion is a fairy common problem, especially if the installed battery is more than 2 years old. Corrosion occurs when the battery acid reacts with the metal terminals which can lead to loss of contact and reduced current flow. If there isn’t enough current flow to crank the engine, the dashboard lights may flicker and you may also hear clicking noise from the starter solenoid when you try to start the engine.

Check battery terminals

To know if your Journey starting problems are from dirty battery terminals, you need to investigate them. Lift the plastic covers over the terminals and check for any signs of corrosion. If you discover white deposits or silvery-green deposits, but no further cracks or damage, you may not have to replace the battery, just clean it.

Clean the battery terminals

Quick cleaning: There is a neat little trick with which you can clean corrosion on the battery terminals of your Journey in under a minute. Pour hot boiling water over the corroded terminals and the corrosion will just melt away. Do one terminal at a time and don’t let water puddle on the top of the battery touch both terminals at the same time, this can short the battery.

Thorough cleaning: To thoroughly clean the battery in your Dodge Journey, you have to remove the terminal cables first, which requires no special knowledge, just a little concentration, as the order is very important. First remove the black cable from the negative terminal using a wrench or a plier. Next you can unplug the red positive terminal cable. Be careful not to touch both terminals with your metal tool, it will be one expensive mistake. Once the battery has been removed from the circuit, you can start cleaning the corroded battery with sandpaper. After cleaning, reconnect the cables in reverse order, positive first, then negative.

3. Bad ground connection

What is a ground connection.

The negative terminal of the battery is connected to the body/chassis of Journey, called a ground connection. The engine also requires a ground connection to function, but the way the engine is mounted, it does not allow the electric current to flow between the engine and the body (due to non-conductive rubber insulated engine mounts). For this purpose, a ground strap/wire is used to connect the engine and the chassis.

What happens when the ground connection goes bad?

If the ground connection of the chassis or the engine goes bad in your Journey due to rust or corrosion, you will face all sorts of electrical issues, including clicking noises, flickering dashboard lights, and no start problem. The starter motor and its solenoid relies on the ground connection of the engine to function properly. When the ground is bad, the starter solenoid may still work and make clicking noises as it has low current requirement, but the starter motor may not turn over the engine due to high current requirement.

How to check if the ground connection is good?

You can check the quality of the ground connection in Journey by doing a conductivity test between the negative terminal of the battery and the chassis/body of the vehicle and the engine. Take a multimeter, change its settings to ohms symbol. Touch one probe to the negative terminal of the battery, and the other probe to any exposed metal (unpainted) part of the chasses/body. The reading should be at or very close to zero ohms. Do the same between the negative terminal of the battery and any exposed metal part of the engine.

Inspect the ground connections

If the conductivity test fails, check the condition of the ground connections in your Journey. Inspect the connectors of the ground cables (battery to body, body to engine) for any signs of rust or corrosion. Clean the contacts with a sandpaper.

There are many reasons why your Dodge Journey dashboard lights flicker and won’t start. When looking for the reason, you should start with the most obvious causes that are easy to diagnose: weak battery, and poor electrical connection.

In any case, it is advisable for laypersons to visit a workshop. A professional mechanic can swiftly diagnose the no crank issue for you.

• Skoda Rapid bad spark plugs symptoms, causes, and diagnosis
• Audi A7 AC blower motor not working – causes and diagnosis
• Audi A8 airbag light is on – causes and how to reset
• Lexus UX airbag light is on – causes and how to reset
• Audi A5 auto windows not working, how to reset
• Lexus UX engine overheating causes and how to fix it
• Ferrari Roma pulls to the right when driving
• VW Amarok makes clicking noise and won’t start – causes and how to fix it
• Ram 4500 Heavy Duty window bounce back when closing – causes and how to fix it
• Ford Fiesta airbag light is on – causes and how to reset
• Ford Focus AC blowing hot air – causes and how to fix it
• Citroen C1 pulls to the right when driving
• Lincoln MKT bad ignition coils symptoms, causes, and diagnosis
• Is Oldsmobile Bravada key fob waterproof?
• Citroen C4 horn not working – causes and how to fix it
• Toyota Fortuner auto windows not working, how to reset
• Enable or disable Hill Start Assist in Jeep Grand Cherokee
• Lexus LC Android Auto not working – causes and how to fix it
• Peugeot 2008 bad mass air flow sensor (MAF) symptoms and causes
• Acura TLX makes humming noise at high speeds – causes and how to fix it

• Fuel Consumption
• Engine Sizes
• Engine Torque
• Engine Power
• Towing Capacity
• Seating Capacity
• Steering Wheel Size
• Dimensions and Weight
• Fuel Tank Sizes
• Trunk Space
• Tire and Rim Sizes
• Bolt Patterns
• Coolers and radiators
• Radiator Fan
• Heat Exchanger
• Intercooler
• Timing Belt
• Sizes of Wiper Blades
• Cabin Filter
• Fuel Filter
• Transmission Fluid
• Antifreeze & Coolant
• Brake Discs
• Brake Drums
• Brake Fluid
• Bulbs For Fog Lights
• Bulbs For Headlights
• Bulbs For Turn Signals
• Bulbs For Licence Plates
• Bulbs For Markers
• Bulbs For Rear Fog Lights
• Bulbs For Backup Lights
• Bulbs For Brake Lights
• Technical Specs
• Car History

• Engine & Fuel
• Coolers and Radiators

Lightning Bolt on Dashboard in Dodge Journey - What’s This?

CarAraC auto mechanics and car experts

Your Dodge Journey has warning lights that illuminate on its dashboard , just like every other modern car. For example; the vehicle security warning, brake warning, airbag warning, battery warning, engine oil pressure warning, etc. Then there's the lightning alert that you may not be familiar with.

Lightning bolt warning lights highlights

• Common reasons: throttle control problems
• How to fix: disconnect the battery for some time, use scanner and get trouble codes
• Possible consequences: you may get stranded
• Priority level: High
• Can you drive? Carefully
• DIY repair: Impossible
• Repair price range: $150-$800

Brief Background to the Dodge Journey

Dodge Journey vehicles are medium-sized crossover SUVs (CUVs) that are issued by the Dodge brand. They were first released in 2009. Then there was a rebadge to the Fiat Freemont in 2011 as a parallel collection. The cars come in right-hand and left-hand drive.

The Dodge Journey comes with warning indicators just like other Dodge models. When these warning lights come up; it could be a system malfunction, security issue, or need for urgent maintenance.

Driver safety shouldn't be taken for granted, especially when a warning light comes on. Taking a related risk could be bad for you and/or the vehicle

What Is the Electronic Throttle Control on a Dodge Journey?

Your Dodge's electronic throttle control features an accelerator pedal module which has a motor, sensors, and a throttle plate. It's a great improvement from the traditional mechanical linkage in old-model cars. Although it isn't immune to mechanical faults.

The ETC measures the pressure drivers apply on the gas/accelerator pedal. The pedal isn't mechanically linked to the engine. A sensor tracks the pedal's position and the data is transmitted to the ETC for engine RPMs (revolutions per minute) to be adjusted.

Gas pedal pressure will determine how much the throttle passage will be opened. There's a flat valve at the opening that's regulated by the pedal's movement. It's called the throttle plate or butterfly valve.

The throttle plate rotates inside the throttle body when you depress the pedal. Then the air will be let into the intake manifold and quickly drawn into it by its vacuum.

1) Sensors in the ETC System

Two sensors that are instrumental to the ETC's operations include the following:

• Mass Airflow (MAF) Sensor

The mass airflow (MAF) sensor calculates the change in airflow. It will then send results to the engine's control unit (ECU) or electronic control module (ECM). This sensor is usually located between the throttle body and the air cleaner.

• Throttle position (TPS) Sensor or Throttle Valve Position Sensor

It's linked to the throttle body and it tracks your Dodge's throttle angle. You can find it on the reverse side of the throttle plate.

Don't get confused about the two sensors mentioned above. The TPS simply informs the ECU/ECM that you've depressed the gas pedal, while the MAF detects the air added. The NAF

2) The Role of the ECU

It's the ECU that controls the balancing of the air-fuel mixture in real-time. It also calculates the best moment to activate the spark plugs to ignite the balanced air-fuel combination.

3) Wide-Open Throttle (WOT)

This is what's referred to as full throttle. It's when the throttle is fully opened on an internal combustion engine or in your car. WOT also means the max-speed state of running an engine or the usual condition of a completely opened butterfly valve or throttle plate.

Your depression of the gas pedal in this situation is referred to as "flooring it". There'll be maximum intake of air because of the lowest resistance to incoming air.

What Does the Electronic Throttle Control Warning Light Mean?

The electronic throttle control warning light on your Dodge Journey could mean that the system has detected a communication problem that has resulted in an ETC error. It's most likely a result of a miscommunication between the ETC and its related sensors.

Dodge Journey vehicles were introduced almost a decade and a half ago, so the dashboard instrument cluster arrangement may vary based on the model year of your car. Still, the lightning symbol is very easy to notice when it illuminates.

Electronic Throttle Control Warning Light Behavior

The electronic throttle control warning light can be a troublesome alert that can come on at any time after the first illumination. And it can go off easily and come on after some days or even weeks. It may stay on for hours in some cases, only to stop when you restart the vehicle.

It will seem like the alert has a mind of its own. Worse still, the symptoms of the fault may not be easy to notice. The car might just be driving just fine regardless of the warning light. There's no need to get confused or nervous.

The ETC light could stay on after the initial indicator check when you first start your car. It could also activate when driving. Even the check engine light (CEL) could activate with it simultaneously.

What To Do Immediately After Noticing the ETC Warning Light

You could continue driving, but it wouldn't be the best move. Just remember to get the car checked at your earliest convenience if you decide to take the RISK.

Drivers could also stop the Dodge instead and park it at a convenient spot or put it in "park". Then proceed to put the engine off and cycle the ignition. The warning light may go off at this point.

Your car should be drivable if the alert doesn't go off. But the vehicle will need to be serviced ASAP. In case of the light flashing, then you should understand that the problem is a severe one that demands more urgency. It won't be advisable to drive the car in such a scenario, but you actually could.

Utilize a diagnostic scan tool to check for vehicle fault codes if you have one. This should be done before any other thing-be it DIY physical checks or hiring a professional technician. It may save you from getting scammed by the dealer or mechanic with a wrong diagnosis and unnecessary repair bills.

Ask the professional or dealer attending to you if they can let you be with them in the vehicle as the diagnoses are taking place. Some repairers offer such a service.

You'll have to take your car to the dealer or auto repair workshop immediately if you don't have a scan tool. Decreased engine power, rough engine noise, or abnormally high idle speed may be experienced if you drive the Dodge while the light is flashing.

Performance issues such as misfiring, stalling, and unstable throttle feedback when the light comes on while driving means you must stop the car. Towing the vehicle to a repairer is recommended at this point if you want to avoid complicating the situation.

Other Symptoms of a Bad ETC

You should look out for the following signs when the ETC alert comes on:

• Idle surges
• Rough idling
• Uninitiated acceleration (car accelerating by itself)
• Reduced fuel mileage (poor fuel economy)
• Engine misfiring

Electronic Throttle Control System Reset Procedure

The problem being indicated by the ETC light might just be the need for a gas pedal reset. The pedal position might not be well lined up or aligned. This will result in a communication error with the sensors that trigger the motor which closes or opens the throttle. Such could be the case in a high-mileage Dodge Journey.

Thankfully, the pedal reset can be done on your own instead of hiring a professional. Follow the steps below carefully to reset the pedal.

• Step 1: Switch on the ignition key without starting the vehicle.
• Step 2: Press the accelerator pedal to the floor and ease it up.
• Step 3: Start the vehicle and depress the pedal again. Observe whether your Dodge will respond or not. Check to see if the ETC light has gone off as well.
• Step 4: Proceed to drive the car around to see if the ETC is working well and if there are no other issues.
• Step 5: Take the car to a repair place if the throttle problem continues and the ETC light is still on.

Most of the warning lights that illuminate on your dashboard can't be taken for granted. And the Dodge Journey electronic throttle control warning light isn't an exception. That's why they're referred to as warnings. Always deal with the lightning symbol alert coming on as soon as possible.

Scanning your Dodge for diagnostic trouble codes (DTCS) will help in eliminating so many possibilities related to the ETC alert. It will save you from diagnostics bills at a repair shop or wasting money on "trial and error". You may only need to do a simple fix such as swapping out the air filter and ETC sensor, or resetting the pedal.

About the authors

The CarAraC research team is composed of seasoned auto mechanics and automotive industry professionals, including individuals with advanced degrees and certifications in their field. Our team members boast prestigious credentials, reflecting their extensive knowledge and skills. These qualifications include: IMI: Institute of the Motor Industry, ASE-Certified Master Automobile Technicians; Coventry University, Graduate of MA in Automotive Journalism; Politecnico di Torino, Italy, MS Automotive Engineering; Ss. Cyril and Methodius University in Skopje, Mechanical University in Skopje; TOC Automotive College; DHA Suffa University, Department of Mechanical Engineering

Add comment

2019 Dodge Journey Owners Manual - Warning lights and messages

Warning lights and messages.

The warning/indicator lights will illuminate in the instrument panel together with a dedicated message and/or acoustic signal when applicable. These indications are indicative and precautionary and as such must not be considered as exhaustive. Always refer to the information in this chapter in the event of a failure indication. All active telltales will display first if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Some telltales are optional and may not appear.

RED WARNING LIGHTS

Seat belt reminder warning light.

This warning light indicates when the driver or passenger seat belt is unbuckled. When the ignition is first placed in the ON/RUN or ACC/ON/RUN position and if the driver’s seat belt is unbuckled, a chime will sound and the light will turn on. When driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Reminder Light will flash or remain on continuously and a chime will sound.

Refer to “Occupant Restraint Systems” in “Safety” for further information.

AIR BAG WARNING LIGHT

This warning light will illuminate to indicate a fault with the air bag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position. This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared. If the light is either not on during startup, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.

BRAKE WARNING LIGHT

This warning light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.

If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.

The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.

The light will remain on until the cause is corrected.

The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions. The vehicle should have service performed, and the brake fluid level checked.

If brake failure is indicated, immediate repair is necessary.

Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately.

Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required.

Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer.

The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.

This light shows only that the parking brake is applied. It does not show the degree of brake application.

VEHICLE SECURITY WARNING LIGHT — IF EQUIPPED

This light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed.

ENGINE COOLANT TEMPERATURE WARNING LIGHT

This warning light warns of an overheated engine condition. If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound. If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool, whichever comes first.

If the light turns on while driving, safely pull over and stop the vehicle. If the Air Conditioning (A/C) system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service.

Refer to “If Your Engine Overheats” in “In Case Of Emergency” for further information.

TRANSMISSION TEMPERATURE WARNING LIGHT — IF EQUIPPED

This warning light will illuminate to warn of a high transmission fluid temperature. This may occur with strenuous usage such as trailer towing. If this light turns on, stop the vehicle and run the engine at idle or slightly faster, with the transmission in PARK or NEUTRAL, until the light turns off. Once the light turns off, you may continue to drive normally.

If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.

Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.

BATTERY CHARGE WARNING LIGHT

This warning light will illuminate when the battery is not charging properly. If it stays on while the engine is running, there may be a malfunction with the charging system. Contact an authorized dealer as soon as possible.

This indicates a possible problem with the electrical system or a related component.

OIL PRESSURE WARNING LIGHT

This warning light will illuminate to indicate low engine oil pressure. If the light turns on while driving, stop the vehicle, shut off the engine as soon as possible, and contact an authorized dealer. A chime will sound when this light turns on.

Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood.

ELECTRONIC THROTTLE CONTROL (ETC) WARNING LIGHT

This warning light will illuminate to indicate a problem with the Electronic Throttle Control (ETC) system. If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem. Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position. The light should turn off. If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.

This light may turn on if the accelerator and brake pedals are pressed at the same time.

If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing. The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer.

ELECTRIC POWER STEERING FAULT WARNING LIGHT

This warning light will turn on when there's a fault with the Electric Power Steering (EPS) system. Refer to “Power Steering” in “Starting And Operating” for further information.

Continued operation with reduced assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible.

DOOR OPEN WARNING LIGHT — IF EQUIPPED

This indicator will illuminate when a door is ajar/open and not fully closed.

If the vehicle is moving, there will also be a single chime.

LIFTGATE OPEN WARNING LIGHT

This warning light will illuminate when the liftgate is open.

YELLOW WARNING LIGHTS

Engine check/malfunction indicator warning light (mil).

The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems. This warning light will illuminate when the ignition is in the ON/RUN position before engine start. If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.

Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing.

When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.

A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others.

Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.

ELECTRONIC STABILITY CONTROL (ESC) ACTIVE WARNING LIGHT — IF EQUIPPED

This warning light will indicate when the Electronic Stability Control system is Active. The “ESC Indicator Light” in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated. It should go out with the engine running. If the “ESC Indicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.

The “ESC OFF Indicator Light” and the “ESC Indicator Light” come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.

The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive.

This light will come on when the vehicle is in an ESC event.

ELECTRONIC STABILITY CONTROL (ESC) OFF WARNING LIGHT — IF EQUIPPED

This warning light indicates the Electronic Stability Control (ESC) is off.

Each time the ignition is turned to ON/RUN or ACC/ON/RUN, the ESC system will be on, even if it was turned off previously.

TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT

The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed.

Should one or more tires be in the condition mentioned above, the display will show the indications corresponding to each tire.

Do not continue driving with one or more flat tires as handling may be compromised. Stop the vehicle, avoiding sharp braking and steering. If a tire puncture occurs, repair immediately using the dedicated tire repair kit and contact an authorized dealer as soon as possible.

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.

As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.

Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.

Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.

The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Using aftermarket tire sealants may cause the Tire Pressure Monitoring System (TPMS) sensor to become inoperable. After using an aftermarket tire sealant it is recommended that you take your vehicle to an authorized dealer to have your sensor function checked.

ANTI-LOCK BRAKE SYSTEM (ABS) WARNING LIGHT

This warning light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.

If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible. However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.

If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.

LOW FUEL WARNING LIGHT

When the fuel level reaches approximately 2 gal (7.5 L), this light will turn on and a chime will sound. The light will remain on until fuel is added.

LOW WASHER FLUID WARNING LIGHT — IF EQUIPPED

This warning light will illuminate when the windshield washer fluid is low.

Refer to “Engine Compartment” in “Servicing And Maintenance” for further information.

GREEN INDICATOR LIGHTS

Park/headlight on indicator light.

This indicator light will illuminate when the park lights or headlights are turned on.

Refer to “Exterior Lights” in “Getting To Know Your Vehicle” for further information.

FRONT FOG INDICATOR LIGHT — IF EQUIPPED

This indicator light will illuminate when the front fog lights are on.

TURN SIGNAL INDICATOR LIGHTS

When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash. Turn signals can be activated when the multifunction lever is moved down (left) or up (right).

A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on.

Check for an inoperative outside light bulb if either indicator flashes at a rapid rate.

CRUISE CONTROL SET INDICATOR LIGHT — IF EQUIPPED

This indicator light will illuminate when the cruise control is set to the desired speed. Refer to “Speed Control” in “Starting And Operating” for further information.

WHITE INDICATOR LIGHTS

Cruise control ready indicator.

This indicator light will illuminate when the cruise control is ready, but not set. Refer to “Speed Control” in “Starting And Operating” for further information.

BLUE INDICATOR LIGHTS

High beam indicator light.

This indicator light will illuminate to indicate that the high beam headlights are on. With the low beams activated, push the multifunction lever forward (toward the front of the vehicle) to turn on the high beams. Pull the multifunction lever rearward (toward the rear of the vehicle) to turn off the high beams. If the high beams are off, pull the lever toward you for a temporary high beam on, "flash to pass" scenario.

Dash lights turning on and off while car is off

My 2015 dodge journey died last night. I think how I know why. My dash lights are turning on and off while the car is OFF. I cant find anything online about what could be the cause. I’ve found a few things about what to do while the car in on but nothing about it happening the a car that’s off.

On some cars the lights stay on for like 30 seconds after the ignition is off. But if they are on all the time even when the light switch is fully off, something is wrong, that is NOT normal.

That happens sometimes due to somebody wiring some accessory to the nearest hot wire, which might be the dash lights wire. That’s fine unless there is another source of power to the device, and that feeds back up the dash lights wire.

The old Audi’s had this bug— if you held the high-beams flash switch, that would feed power back into the accessory circuit, even when the key was out. They considered that a “feature” not a “bug”, as it let you close the sunroof without the key.

Anyway, if someone has done some wiring lately, that’s probably the problem. Has someone added a security system, a radio, an amplifier, or something else electrical? That’s probably it.

If nothing has been messed with lately, then it’s likely that there is a short in the module that controls the lights. In the olden days the lights had a regular plain old switch, those very rarely failed. Today they use transistors to do the switching and they do sometimes fail, usually shorting out. They can be helped along toward shorting out if someone accidentally shorts out the cigar-lighter power outlet, with like a bad charger cord.

It can also be a faulty door latch switch inside the door…thinking the door has been opened. The days of pin switches in the door jamb have seemed to go the way of the Dodo Bird…the way its done these days is inside the door latch. That sensor could be on the verge of open/close and it fluctuates back n forth.

A good engine diag scanner will show you live data of these things…and even allow you to manipulate items on and off. Without this piece of equipment you are flying blind.

Heres a trick for ya… Open the drivers door (Most suspect door and switch btw)…use a phillips screwdriver sideways inside the door latch to simulate the door being closed onto its lock hasp…this will simulate a closed door while it is still open… IF you have no probs during this test…it shows the latch is not going onto the hasp far enough to fully trigger the switch inside the door.

ALL of this assumes you dont actually have door pins in the door jamb to indicate a closed door… Methinks unlikely on a 15’…but you never know these days…so see what system your vehicle uses to know the door was closed…no door pins…then its in that door latch on the door.

Fairly easy test

Fuse 130–15 amp, you could try pulling that fuse to see if it will stop instrument lamps. I realize, courtesy lamps will stay on for a bit after exit, I didn’t realize dash would stay on? I don’t know if link will highlight or not? Pulling the fuse may allow cluster to reset?

The problem might be caused by a faulty Totally Integrated Power Module.

Could be a bad ground connection somewhere inside the dashboard.

• Forum Listing
• Marketplace
• Advanced Search
• Dodge Truck, SUV and Van Forums
• Dodge Ram Truck 3rd Gen (02 – 08) Forums
• 3G Dodge RAM - General Talk

All Warning lights on while driving

• Add to quote

A unique situation occured this week (it was a wet slushy week) While driving my 2008 Ram 4x 4 home at 50- 60 mph after a busy day with it, moving daughters furniture , the dashboard lit up with every warning light, and speedo went dead, and then a few seconds later it would all come back on , engine did not die,truck kept running, it continued to do this randomly about 12 times over the course of the hour drive home. I brought it to dealer next morning, it only did it once while the service tech was writing the milieage down to bring it inot shop, but did not do it for the actual mechanic . The mechanic put on computer readout tool and yes it did show that truck "lost communication" a dozen times that day and the one more time that day. But they were unable to pinpoint the problem. No fault codes other than "lost communication". They gave it back to me and suggested we see if it clears it self up or wait till it does it again (and do what ?) they only charged me 65 bucks because they felt bad could not find. Anyway, this truck has 80,000 km (so 50,000 miles) I have made no electrical changes to it, no other problems. It is a cold and wet environment up here so maybe a bad connector that has dried it self out since then . It has not done the warning lights again today when I drove it. Any ideas or similar problem that you got fixed ????  

Just a haunch but check the ground wire from the battery to the chassis. Make sure all the wires are tight to the terminal and that the terminals are clean.  

I second that.. The ground is most important..  

Fred had that problem it would come and go intermittenly. Turned out to be the fuse box. He repalaced it. You can check the connector's under it to make sure there clean and tight. Maybe try grabbing the wire connector underneath and wiggling it to see if the problem show's up.  

Lost communication with what module? The code always tells you what module it lost communication with. If all the lost communication codes say cluster then you probably have a cluster going out on you. Tell the dealer to run a Loss of Comm. test through wiTech. If they don't know what you are talking about then go to another dealer.  

thanks guys, I would assume dealer mechanic would of checked ground from battery, but I will double check and alos wiggle the fuse box to see if I can make it happe. I had the trucl oilsprayed in November 2012 , maybe it got into somewhere it shouldn't of. Also will suggest to dealer to do the witech thing if it does it again.  

Well update it has only got worse but more random. I took apart all the battery connections and cleaned and the ground to the body fender and large connection on outside of fuse box. reset computer , tested gauges using that method of holding odometer reset while turning key to on, and all supposedly okay. But still randomly while driving all warning light and chimes come on and guages die and then a few seconds later back to normal and does this a dozen times while driving in to work. then next day will not do it at all , same road same bumps , same temp. Dealer only sees advantage to see it if it is doing it while they are looking at it. Of course it is never doing it when I drive by the dealer !!! I checked all the plugs under the seats too. I am ready to trade this in and look at buying a pre 1980 vehicle without all these computer aspects to go wrong !!  

TIPM!! had the sam situation, all warning lights on and off.....turned out I needed to have the TIPM replaced....only cost about $700 CDN Oh and I have a 2008 5.7 1500 4x4.  

I knw this is off topic but i have been looking at other posts about the foglight bypass for being able to keep you foglights on while you are running with your highbeams. But does anybody know how to do this on a 2006 ram 4.7 Can anybody help me with this??? \  

Hosey........maybe dumb question but what does TIPM stand for and tell me more about how your dealer figured out it was that ? please and thanks  

Yup, Total Integrated Power Module. I never heard of such a thing till about 2 months ago. I was driving down the road (it was the first snowfall of the season). I went 5 mins down the road and got to the hardware store and parked. Then bam....all lights on the dash, warning bells.....I sat for a minute and did the whole WTF. turned the truck off and then back on and nothing....as if nothing happened. The roads were wet and sloppy snow slush crap. A few days later was in the truck, flipped it into 4x4 and then BAM....lights, warnings, and then the truck died! nothing.....it would even turn over....I finally got it to turn over, and dropped it off at the dealership (it was the nearest shop, only reason). They plug it in and tell me the TIPM died. Im not a mechanic but the issues that i was having woth the truck were all electrical and speratic.... This might not be your issue with your truck but the thread title "warning lights" caught my eye. good luck bro.  

The TIPM's replaced most of the fusebox. Personally, I don't like it. On paper it's cheaper for manufacturing, simpler to check and replace, cleaner under the hood, and when it fails, it gives Dodge and the dealership a much bigger payday under your hood. :imo  

• ?            
• 294.8K members

Top Contributors this Month

tilt all the dashboard lights

Did you find the website helpful?

• Remember me Not recommended on shared computers

Forgot your password?

• Electrical, Battery & Charging

Help required ETC warning light on dash

• etc warning light on my dash

By grahamcook October 8, 2022 in Electrical, Battery & Charging

• Reply to this topic
• Start new topic

Recommended Posts

Hello i have had this warning light appear on my dash , and had a loss of power , does this mean my throttle body needs replacing ??, also  once i finally got the car home there seemed to be a burning smell coming from the car , can anyone help please ??my vehicle is a dodge journey 2013

Link to comment

Share on other sites.

$ or 6 cylinder motor? miles on the car? any maint. been done like spark plugs or any sensors?

  All important items to include to get decent suggestions back to you.

6 cylinder , its at about 150k km , no maintenance done for a while plugs and sensors not done in a while 

the maintenance is done on time it  was running fine until ETC light come on , i done the shut of thing and the light did go off but after a short drive it come back on , and the light stays solid its not flashing

have you had it scanned for any codes? that will lead you in the right direction without throwing parts at it..... a solid warning light means you have a problem but still okay to drive it to get it fixed, a flashing warning light means to shut it off and have it towed or damage will happen to your journey...you might be able to clean it first before replacing it depends on your situation on $$ and parts available check out you tube for vidios on how to clean or replace such part but id get it scanned first for codes

• John/Horace

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account. Note: Your post will require moderator approval before it will be visible.

×   Pasted as rich text.    Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.    Display as a link instead

×   Your previous content has been restored.    Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

• Insert image from URL
• Submit Reply
• Existing user? Sign In

More Forum Apps

• Online Users
• Leaderboard

|| Forum Activity ||

• All Activity
• Create New...

CarComplaints.com : Car complaints, car problems and defect information

Latest news.

• Aug 23: Ford Bronco Sport and Maverick 12V Battery Investigation Closed
• Aug 21: BMW Water Pump Recall
• My Account |
• Investigations
• Search Complaints
• Update Carcomplaints
• Add Complaints
• Recent Trends
• Best Vehicles
• Worst Vehicles
• Worst Complaints

Donate your DODGE RAM 1500!

Is it time to move on? Support NPR & the programs you love. Donate your old car in minutes through the CarTalk Vehicle Donation Program.

• Dodge »
• Ram 1500 »
• 2001 »
• accessories - interior
• Lamborghini
• Mercedes-Benz
• B2500 Cargo Van
• Conversion Van
• Grand Caravan
• Power Ram 50
• Ram 2500 Power Wagon
• Ram Conversion Van
• Ram Van 1500
• Ram Van 2500
• Ram Van 3500

Cracked Dashboard

2001 dodge ram 1500 (page 1 of 31).

• « back to accessories - interior
• Complaints 2K
• Crash Tests 1
• Ram 1500 Recalls 16
• Defect Investigations 2

Most Common Solutions:

• Dodge should issue a recall (386 reports)
• replace dash (126 reports)
• not sure (83 reports)
• bought a dash cover (8 reports)
• glue it back together (5 reports)
• dodge needs to pay for 1/2 or all the cost of parts/repair (2 reports)

accessories - interior problem

Unsubscribe any time. We don't sell/share your email.

Helpful websites

• Full Replacement Dash - After market full replacement dash with lifetime warranty.
• Real True 10 Minute Dodge Cracking Dash Remedy - This is a youtube link from a auto / truck show showing a very simple real remedy for the thousands of Doge, Chevy (and others) dash cracking issue.This is a 10 minute part/fix. Please watch this is real and will help you.
• Dodge Ram Cracking Dashboard Lawsuits - From the website: " If your Dodge Ram has experienced a defect in its dashboard that goes beyond normal wear and tear, you might be eligible to file a Dodge Ram Defective Dashboard lawsuit. We are currently offering free legal consultations to owners and lessees of 1998-2007 "

Find a good Dodge mechanic

A free service from CarTalk.com

Search for Car Problems

Example: "Bad Brakes", "Toyota Recall", etc.

2001 Dodge Ram 1500 Owner Comments (Page 1 of 31)

Jan 01 2009

Ram 1500 Sport 5.9L

• Automatic transmission
• 90,000 miles

A D V E R T I S E M E N T S

Not much to say that hasn't been said about the cheap dash they put in their number one truck. Mine is completely gone, the pieces fly off and partials that are left get into my and my kids eyes all the time. Forget about trying to replace any parts because nothing will attach! I have everything holding together with black duct tape!

- Jason K. , Apache Junction, AZ, US

Jan 02 2010

Ram 1500 V8

• 98,000 miles

Was in a car accident, and the plastic pieces to the broken dash shot off and hit my face when airbags deployed, cut my artery, I had to have over $500,000 in reconstructive surgery. There’s so much nerve damage I can’t feel my face. On top of half of it being metal plates! I’m so lucky to be alive. Why can’t you just do what’s right and fix the problem? You take bailouts and tax cuts, on top of making millions. Do what’s right and fix your error. Lord forbid this happens to anyone else.

- Collin L. , Austin, US

Feb 04 2008

Ram 1500 Sport V8

• 30,000 miles

Dodge needs to fix this ... please!

- thealarmguy40 , Eureka, US

May 01 2014

Ram 1500 ST 5.2L

• 70,000 miles

The dash cracked all over -had to put a cover on top. Color does not match but looks better. Hopefully will never have to remove to work on heater core.. Contacted Dodge- dealer took pictures and sent to corp who turned down claim- as usual vehicle was over 3yrs old.

- tom s , Sophia, US

Sep 01 2013

Ram 1500 Larime V8

• Manual transmission
• 105,000 miles

click to see larger images

This is a known problem for Dodge trucks in this time frame. If this vehicle were to be in an accident sufficient to deploy the airbags, sharp plastic shards would be propelled everywhere, including the face and eyes.

- Gary K. , Pleasanton, US

Search CarComplaints.com for these popular complaint phrases...

Aug 01 2015

I would be happy to pay the cost of the replacement dash if it was at cost. Some dealers want over $700 just for the part other online dealers will go as low as $400 but you have to ship it. Dodge could sell it to us for $100 and not lose a penny. They would rather make a profit off their faulty product.

- Marc T. , South San Francisco, CA, US

Apr 06 2016

• 60,000 miles

I looked into having the dash replaced and was given a price of more than $2000. This is too much for me to be expected to pay to repair a defect that is totally Dodge’s fault. There should be a recall on this.

- jcart , Austin, US

Apr 01 2011

The plastic dash cover has severely cracked in multiple places with whole pieces becoming dislodged. Dash continues to disintegrate and I'm worried it will be an issue for the electrical and mechanical components within the dash housing and possible causing undue malfunctions, failure or fire and unnecessary repairs to other internal components, but mostly if it could possibly interfere with the deployment of the passenger airbag should an accident happen.

- Brian H. , Richmond, US

Jun 01 2006

Ram 1500 5.2L V8

• 97,000 miles

My dash is so cracked up that I had to put something over it to keep pieces from coming out when you hit a bump. Sometimes more often than not, the rpm gauge or the speedometer doesn't work. Something needs to be done. I'm a disabled veteran on a fixed income and I can't afford to pay to have it fixed.

- Linda B. , Fayetteville, NC, US

Apr 01 2010

Ram 1500 Sport 5.2L

• 65,000 miles

Shameful that a company would market a total POS product then refuse to fix what they F-ed up.

- Jack M. , Zebulon, NC, US

Apr 15 2018

Ram 1500 Laramie SLT 5.2L V8

• 235,000 miles

This is not merely a cosmetic issue. Actual pieces of the dash have broken off. Heaven help me in an accident. My own vehicle will be my worst enemy.

- Daniel E. , Huntley, IL, US

Sep 01 2008

Ram 1500 4x4

• 52,000 miles

Dodge knows its product is defective and needs to fix it. If Dodge wants LOYAL customers it needs to make this right.

- Oswaldo P. , Albuquerque, NM, US

Jan 10 2018

Ram 1500 ST 3.9L V6

• 122,220 miles

The dash, in its entirety, cracked into chunks, all of which are deadly in the event of an accident. The dash board and bezel, in a period of months has completely cracked across its entire width and breadth, chunks are all sharp and, in the event of an accident, present a potential for egregious bodily harm, entirely the fault of the manufacturer. Dodge should take responsibility for this malfeasance and should make the dash board and bezel, both of which have become a deadly liability, to anyone who owns this vehicle. It has never been a habit of Dodge/Daimler/Chrysler to let persons risk their lives or their well being due to any design failure(s) on their part, nor should such a habit begin now. No constabulary in these United States would allow such failure go unchecked were such failings a part of any individual or organization, and that would include Dodge and its subsidiaries. What then will be the solution. Continually claiming this design failing is a "cosmetic" issue does in no way relinquish Dodge from their part in causing this disaster and the potential for harm to innocent parties who, trusting in our system of government and laws set forth to protect our citizens, purchased this Dodge product in good faith. It is the sole responsibility of Dodge and its dealerships and their subsidiaries to make this failure aright in compensation.

- rorywitt , Grandfield, US

Mar 01 2012

Ram 1500 Lariat 5.2L V8

• 114,000 miles

Apparently this seems to be a major problem for an awful lot of this years Dodge P/U trucks. It should be recalled. Definitely a safety issue. If someone had an accident the dashboard pieces could do some damage to your face or chest. Thank you for listening.

- skull54 , Williamstown, US

Jun 01 2010

Ram 1500 SLT 5.9L

• 32,815 miles

Dash started cracking, then large pieces starting falling in, now have it held together with gorilla tape.

- Howard D. , Evansville, US

Oct 21 2016

Ram 1500 Laramie Slt V8

• 100,600 miles

THE DASH IS CRACKED AND IS FALLING APART IN MY RAM 1500. CUP HOLDER IS FALLING OFF AND THE GLOVE BOX DOOR IS BROKEN. I REPLACED THE COVER OVER THE SPEED OMETER AND PUT A DASH COVER ON THE DASH BUT THE MAIN DASH IS NOW FALLING APART. THE LOCAL BODY SHOP SAYS THERE ARE NO AFTERMARKET REPLACEMENT PARTS AND THE REPAIR IS TOO COMPLICATED FOR ME TO DO.

- larrywarren , Center, US

Sep 00 2004

Ram 1500 ST 5.2L V8

• 65,615 miles

About four years into ownership heard a loud crack while driving down road,came to find out that was my dash cracking. Followed by more of the same had other vehicles of older age and never heard of such a thing. Had a Volvo that had stress cracks (spider like from a center point ) can only guess that problem stems from faulty material or manufacturing process noticed that plastic parts were made in mexico? Problem is very scary as in an accident flying shards could be very dangerous especially the pieces near the passenger side air bag. I had applied armor-all to dash,rubber and trim pieces religiously to no avail appears it was money thrown away on this problem it was great on Chevy's ,Mercedes and Ford trucks maybe I just picked the wrong brand to by. In addition to defective plastic have seen the same lack of qualty on door bottoms (Rusting from the inside out and also above fender by truck bed Both from the inside out)

- Bob B. , Wapakoneta, OH, US

Aug 17 2005

Ram 1500 Laramie 5.2L V8

• 68,000 miles

dodge needs to fix this problem and stop saying them are the longest lasting trucks on the road

- Kristy & Jim W. , Wood River, IL, US

Jun 28 2017

Ram 1500 PK 1/2 TON 3.9L V6

• 100,000 miles

The front bezel and dashboard is all in pieces and needs to be replaced. It is obvious the dashboard and bezel were cheaply made. There are several thousand complaints on this website and Dodge needs to replace this immediately before someone gets hurt or killed.

- Darrell B. , Austin, TX, US

Jul 03 2017

Ram 1500 318 V8

• 230,000 miles

I'm very disappointed in DODGE that they haven't fix this issue with the dashboards. They know it isn't the vehicle owner's fault that this issue happened. I had a 2000 dakota that I never did anything as far as cleaning and maintenance on the interior and it didn't have any issues with the dash. So why blame it on the owner for not taking care of it. They know know exactly what caused it.

- Patrick R. , El Dorado Springs, US

Read the next 20 complaints »

DON'T WASTE YOUR TIME: Link must be about this specific problem or it will be deleted — it must be free & helpful, like a video or web page or forum thread about this exact problem. NO FORUM HOMEPAGES. If you have a for-profit service, contact us .

Preview your link:

Not what you are looking for?